Best Quality NACE NACE-CIP1-001 Exam Questions ValidExam Realistic Practice Exams [2023]

Critical Information To Coating Inspector Level 1 Pass the First Time

NACE-CIP1-001 certification exam is a globally recognized program that certifies individuals as coating inspectors. NACE-CIP1-001 exam is conducted by the National Association of Corrosion Engineers (NACE), which is the world’s leading organization that aims to prevent corrosion and protect the environment. Coating Inspector Level 1 certification program is designed to assess the knowledge and skills of individuals in the field of coating inspection and provide them with the necessary credentials to advance their careers.

NACE-CIP1-001 certification exam covers a wide range of topics related to coatings and corrosion protection, including surface preparation, coating application, quality control, and safety procedures. It is a comprehensive exam that tests an individual's understanding of the industry standards, best practices, and regulations related to coatings and corrosion protection. Passing the exam requires a thorough understanding of the subject matter and the ability to apply that knowledge to real-world situations.

NACE-CIP1-001 certification exam covers a broad range of topics, including surface preparation, coating types, application methods, inspection techniques, and safety practices. Professionals who pass NACE-CIP1-001 exam demonstrate that they have a comprehensive understanding of the principles and practices involved in the coatings industry. Coating Inspector Level 1 certification is highly valued in the industry as it ensures that the certified individuals can perform their duties effectively and efficiently, helping to prevent costly mistakes and ensure the longevity of protective coatings.

 

NEW QUESTION # 47
Checking is

• A. a very small hole in a coating caused when air or solvent is trapped in porous film and then escapes.
• B. an exposed area of the substrate or previous coat material, caused by poor application technique.
• C. surface breaks in the film that often result from grease or oil contamination and revel the substrate.
• D. a fine crack in the surface of a coating that rarely reaches the substrate

Answer: D

NEW QUESTION # 48
NACE No. 4/SSPC-SP-7 is a joint standard for

• A. near-white metal blast cleaning.
• B. white metal blast cleaning.
• C. commercial blast cleaning.
• D. brush-off blast cleaning.

Answer: D

NEW QUESTION # 49
As a NACE Coating Inspector your responsibility with respect to safety is to:

• A. Check the credentials of the Safety Officer on site
• B. Assume the role of the Safety Inspector
• C. Check the PPE used by the Applicators
• D. Act in accordance with the site safety requirements and set an example

Answer: D

NEW QUESTION # 50
Passivation can best be described as:

• A. Complete elimination pf the corrosion process
• B. A protective metallic oxide surface layer that slows corrosion
• C. A coating layer applied to the surface to inhibit corrosion
• D. Treating metal with a liquid inhibiter

Answer: B

NEW QUESTION # 51
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:

• A. Advise the Contractor he can proceed
• B. Advise the Contractor of your readings
• C. Advise the Contractor he cannot proceed
• D. Call your supervisor

Answer: B

NEW QUESTION # 52
NACE Level 1 Inspectors have been trained to perform:

• A. Visual inspection only
• B. Visual inspection, Non-Destructive and Destructive testing
• C. Visual inspection and Non-destructive testing
• D. All types of inspection

Answer: C

NEW QUESTION # 53
To achieve consistently accurate results with ALL alt test equipment

• A. wear gloves when sampling.
• B. wash your hands before sampling.
• C. avoid placing the sample discs on a surface.
• D. calibrate the instrument in the field.

Answer: B

NEW QUESTION # 54
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?

• A. 75 Gauge Readings resulting in 25 Spot Measurements
• B. 105 Gauge Readings resulting in 35 Spot Measurements
• C. 45 Gauge readings resulting in 15 Spot Measurements
• D. 225 Gauge Readings resulting in 75 Spot Measurements

Answer: D

NEW QUESTION # 55
The primary difference between Non-Convertible vs. Convertible coatings is:

• A. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
• B. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
• C. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
• D. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do

Answer: D

NEW QUESTION # 56
If inspectors identify issues of non-conformance during an inspection, they should

• A. perform additional tests secretly to ensure there are no other potential issues at the site
• B. instruct the contractor's personnel in how to correct the issue so the project is not delayed
• C. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
• D. wait until the final report is being prepared to identify the issues in writing so they are fully documented

Answer: C

NEW QUESTION # 57
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:

• A. Document the problem and advise the Contractor and Owner's representative
• B. Break the blisters to see what's inside
• C. Document the problem and advise the Contractor
• D. Extract any liquid that may be inside the blister and send it to the lab for further analysis

Answer: A

NEW QUESTION # 58
Which one of the following documents is the best source for coating technical data:

• A. Safety Data Sheet;
• B. Application Guidelines
• C. Specification
• D. Technical Data Sheet

Answer: D

NEW QUESTION # 59
Inspector's daily reports are used:
Select All That Apply

• A. To aid in arbitration between the contractor and client
• B. To provide continuity between inspectors
• C. To help in cases of a coating failure
• D. By the contractor to estimate the amount of work done that day

Answer: A,B,C,D

NEW QUESTION # 60
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:

• A. Level 1
• B. Level 2
• C. Level 3
• D. Level 4

Answer: C

NEW QUESTION # 61
Dew point is the temperature at which

• A. the air is saturated.
• B. humidity decreases
• C. water freezes.
• D. condensation occurs.

Answer: D

NEW QUESTION # 62
Safety Data Sheets must be carefully reviewed by:

• A. All personnel involved in the job
• B. The Application personnel
• C. The Owner's personnel
• D. The Inspection personnel

Answer: A

NEW QUESTION # 63
An Inspector should change position when:

• A. Only when directed by the supervisor
• B. The Inspector is convinced by verifiable facts
• C. The Inspectors position is not the majority position
• D. The Owner can save some money by the change

Answer: B

NEW QUESTION # 64
The NACE Inspector should perform tests for soluble salts:

• A. After surface preparation
• B. Prior to surface preparation
• C. Prior to coating application
• D. When specified

Answer: D

NEW QUESTION # 65
Check abrasive blast pressure with a

• A. surface comparator
• B. replica tape
• C. needle pressure gauge
• D. nozzle aperature gauge

Answer: C

NEW QUESTION # 66
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:

• A. Presence of weld spatter may produce a false positive
• B. Ultra-Violet light may contaminant the surface
• C. Synthetic oil or grease may not be identified
• D. Chloride salt may produce a false positive

Answer: C

NEW QUESTION # 67
You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners' representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.
As a NACE CIP Level 1 Inspector your preferred course of action is to:

• A. Hire a third patty to assist you in understanding the document
• B. Minimize your lack of understanding and go ahead with the inspection task to the best of your ability
• C. Carefully review the document and do the best you can
• D. Advise the owners' representative of your lack of knowledge in this area

Answer: C

NEW QUESTION # 68
ISO SA 2 is defined as:

• A. Very Thorough Blast Cleaning
• B. Thorough Blast Cleaning
• C. Light Blast Cleaning
• D. Near White Metal Blasting

Answer: B

NEW QUESTION # 69
......

NACE-CIP1-001 EXAM DUMPS WITH GUARANTEED SUCCESS: https://www.validexam.com/NACE-CIP1-001-latest-dumps.html

Best Quality NACE NACE-CIP1-001 Exam Questions: https://drive.google.com/open?id=1p1LLzCqqPtkbN2M4-dS1IlZRmMBx_ONQ