Guide (New 2025) Actual NFPA CFPE Exam Questions

CFPE Exam Dumps Pass with Updated 2025 Certified Exam Questions

NEW QUESTION # 49
What is the maximum number of stones below grade that may be occupied for a non-sprinklered assembly occupancy of Type III (211) construction?

• A. Zero
• B. Three
• C. Two
• D. One

Answer: D

Explanation:
According to NFPA 101, Life Safety Code, for a non-sprinklered assembly occupancy of Type III (211) construction, only one story below grade may be occupied. This limitation is intended to ensure safe egress for occupants during an emergency. Additional levels below grade increase the risk and complexity of evacuation, especially in the absence of an automatic sprinkler system.

NEW QUESTION # 50
Exhibit.


What is the approximate maximum available water indicated on supply graph 2 on plan F0.2?

• A. 980 gpm (3,709 Ipm)
• B. 3,980gpm(15,066lpm)
• C. 1,680 gpm (6,359 Ipm)
• D. 1.980gpm (7,495 Ipm)

Answer: D

Explanation:
The graph labeled as"Water Supply Graph N°2"presents a standard water supply flow test summary, which indicates the relationship between pressure (psi or kPa) and flow (gpm or Lpm) for a specific system or hydrant.
How to interpret the graph:
* Static Pressure:
* This is the pressure measured when there is no water flowing, shown at the highest point on the left side of the graph (indicated as approximately 100 psi or 689 kPa in this case).
* Residual Pressure:
* This is the pressure available when water is flowing at a specific rate. The residual pressure line decreases as flow increases, indicating that the pressure reduces when water is drawn from the system.
* Maximum Available Water:
* Themaximum available wateris the point where the system can deliver the highest possible flow (gpm) before the residual pressure reaches a critical minimum level, indicating the system's limit.
* Flow at Maximum Available Water:
* In this specific graph, the point marked asMaximum Available Wateris where the flow reaches
1,980 gpm(7,495 Lpm). This is derived by following the flow axis (horizontal axis) until it intersects with theMaximum Available Watercurve on the graph.
Why the Correct Answer is C (1,980 gpm):
* By following the plotted line for residual pressure, the graph shows that the maximum flow attainable from the system is1,980 gpm(7,495 Lpm) before pressure drops too low. This value represents the system's maximum water supply capacity under normal operating conditions.
This analysis is consistent with the flow rates displayed on the graph and matches the key markers labeled, which indicate the operational limits of the system.
NFPA Relevance:
In fire protection and water supply systems, understanding the maximum available water flow is essential for ensuring that sufficient water can be delivered in the event of a fire. This calculation is particularly relevant in the context of NFPA 20 (Standard for the Installation of Stationary Pumps for Fire Protection) and NFPA 25 (Standard for the Inspection, Testing, and Maintenance of Water-Based Fire Protection Systems), as these standards require that water supply systems are capable of delivering adequate flow to suppression systems under expected fire conditions.

NEW QUESTION # 51
Exhibit.

On plan C1 what is the widthof the fire department access driveway on the south facing side of the building wing closes! lo Bedford Street?

• A. 24 ft (7.3 m)
• B. 16 ft (4.9 m)
• C. 18 ft (5.5 m)
• D. 20 ft (6.1 m)

Answer: C

NEW QUESTION # 52
Exhibit.

On plan sheet P01 fire protection symbols that are square with a solid dot indicate

• A. sprinkler head recessed pendent intermediate temperature quick response
• B. sprinkler head recessed pendent ordinary temperature quick response
• C. upright open sprinkler head for deluge system
• D. sprinkler head upright intermediate temperature quick response

Answer: B

Explanation:
On the plan sheet P01, the fire protection symbols that are square with a solid dot typically represent a recessed pendent sprinkler head designed for ordinary temperature, quick response. This symbol is used in NFPA standards, particularly in NFPA 13, to indicate sprinkler types and their installation characteristics.
Recessed pendent sprinklers are installed to protect against fire hazards from the ceiling downwards, and their quick response mechanism helps to control fires rapidly in occupied spaces.

NEW QUESTION # 53
Exhibit.

What is the occupant load for the woodworking shop in the figure?

• A. 15 people
• B. 10 people
• C. 3 people
• D. 7 people

Answer: D

Explanation:
To determine the occupant load for the woodworking shop, we use the standard occupant load factor provided in NFPA 101, Life Safety Code. For an industrial occupancy like a woodworking shop, the typical occupant load factor is 100 square feet per person. The shop is 750 square feet (69.7 square meters), so dividing the total area by 100 square feet per person gives an occupant load of 7.5, which rounds down to 7 people.

NEW QUESTION # 54
The tops of wall mounted audible fire alarm notification appliances shall be a minimum of what height above the finished floor'?

• A. 90 in.(2.29 m)
• B. 96 in (2.43 m)
• C. 80 in. (2.03 m)
• D. 88 in (2.23 m)

Answer: C

Explanation:
According to NFPA 72, National Fire Alarm and Signaling Code, the tops of wall-mounted audible fire alarm notification appliances should be mounted at a minimum height of 80 inches (2.03 meters) above the finished floor. This height ensures that the devices are installed at an optimal position for sound propagation while remaining accessible for maintenance and testing.
Top of Form
Bottom of Form

NEW QUESTION # 55
A 4 in. (101.6 mm) riser requires what minimum diameter pipe for the combination mam drain and alarm test connection?

• A. 1 1/4 in.(31.7 mm)
• B. 3/4 in. (19.05 mm)
• C. 1 in. (25.4 mm)
• D. 2 in. (50.8 mm)

Answer: C

Explanation:
For a 4-inch (101.6 mm) riser, the minimum diameter pipe for the combination main drain and alarm test connection should be 1 inch (25.4 mm). This size is specified to ensure adequate water flow during a test or when draining the system, in accordance with NFPA 13, Standard for the Installation of Sprinkler Systems.

NEW QUESTION # 56
Seating for more than 200 persons in assembly occupancies, when not fastened to the floor, shall be fastened into groups with a minimum of how many chairs?

• A. Three
• B. Seven
• C. Nine
• D. Five

Answer: D

Explanation:
According to NFPA 101, Life Safety Code, in assembly occupancies where seating is not fastened to the floor, chairs must be fastened together in groups of at least five chairs. This requirement is intended to maintain orderly evacuation and prevent chairs from becoming obstacles during an emergency (NFPA 101, Section 12.7.8.3).

NEW QUESTION # 57
Which one of the following is a legal order to provide documents or testimony during legal proceedings?

• A. Enabling act
• B. Freedom of information act
• C. Affidavit
• D. Subpoena

Answer: D

Explanation:
A subpoena is a legal document that orders an individual or entity to provide documents or testify during legal proceedings. It is a formal demand issued by a court or other legal authority to obtain evidence or witness testimony. Unlike the other options, which may pertain to broader legal frameworks or voluntary disclosures, a subpoena has the force of law compelling compliance.

NEW QUESTION # 58
What is a plat plan?

• A. An architectural site plan
• B. A survey map of a given geographical area
• C. A civil site plan
• D. An overall project layout

Answer: B

Explanation:
A plat plan, or plat map, is a survey map that shows the divisions of a given geographical area. It typically outlines property boundaries, lot dimensions, easements, and rights of way. This type of plan is used primarily for land development, real estate, and legal purposes, providing a detailed view of how land is subdivided.

NEW QUESTION # 59
What is the occupancy classification of a restaurant, if it has an occupant load greater than 50 people?

• A. Assembly
• B. Kitchen
• C. Mercantile
• D. Business

Answer: A

Explanation:
According to NFPA 101, Life Safety Code, and NFPA 5000, Building Construction and Safety Code, a restaurant with an occupant load greater than 50 people is classified as an "Assembly" occupancy. An Assembly occupancy is defined as an occupancy used for a gathering of 50 or more persons for deliberation, worship, entertainment, eating, drinking, amusement, awaiting transportation, or similar uses. Since the restaurant has an occupant load greater than 50 people, it falls under this category.
For exact details, refer to NFPA 101 (Life Safety Code), Chapter 3, and NFPA 5000 (Building Construction and Safety Code).

NEW QUESTION # 60
If a sprinkler system is supplied with water from a gravity tank, the gravity tank shall be installed in accordance with what standard in order to be acceptable as a source of water?

• A. NFPA20
• B. NFPA22
• C. NFPA24
• D. NFPA13

Answer: B

Explanation:
If a sprinkler system is supplied with water from a gravity tank, the tank must be installed in accordance with NFPA 22, Standard for Water Tanks for Private Fire Protection. NFPA 22 provides the requirements for the design, construction, installation, and maintenance of water tanks used for fire protection. It ensures that the gravity tank meets the necessary standards to be a reliable and effective water source for the sprinkler system.
Top of Form
Bottom of Form

NEW QUESTION # 61
What is a plans review checklist used for?

• A. An all-inclusive code requirement list used by both the plan submitter and plan reviewer
• B. An internal guide for plans examiners to avoid overlooking important design aspects
• C. A complete list of mandatory code requirements for specific plan reviews
• D. A guideline for contractors to follow in organizing documents for the plan reviewer

Answer: B

Explanation:
A plans review checklist is an internal guide used by plans examiners to ensure they do not overlook critical design aspects during the review process. It helps standardize the review procedure, making sure all essential code requirements and safety measures are considered before approving a plan. This tool is crucial in maintaining consistency and thoroughness in the plan review process.

NEW QUESTION # 62
The responsibility to promulgate rules that cover plan review is established by

• A. NFPA 220.
• B. NFPA 101.
• C. NFPA 1.
• D. NFPA 170.

Answer: C

Explanation:
The responsibility to promulgate rules covering plan review is established by NFPA 1, Fire Code. NFPA 1 provides guidelines and regulations for the enforcement of fire safety codes, including requirements for plan reviews, inspections, and other fire prevention measures. It is the overarching code that jurisdictions often adopt to ensure uniform fire safety standards.

NEW QUESTION # 63
A fire department access road shall be provided such that any portion of an unsprinklered facility is located no more than what maximum distance from the access road'-'A.

• A. 450 ft (137 m)
• B. 50 ft (15 m)
• C. 150 ft (46 m)
• D. 300 ft (91 m)

Answer: C

Explanation:
According to NFPA 1, Fire Code, a fire department access road must be provided so that any portion of an unsprinklered facility is no more than 150 feet (46 meters) from the access road. This requirement ensures that emergency responders can reach all parts of the building quickly and efficiently in the event of a fire or other emergency.

NEW QUESTION # 64
Which one of the following is a vertical view of a building as if it were cut into two parts?

• A. Elevation view
• B. Floor plan
• C. Sectional view
• D. Detailed view

Answer: C

Explanation:
A sectional view (or cross-section) is a vertical view of a building as if it were cut into two parts, showing the interior details along the plane of the cut. It is used to illustrate the internal construction, layout, and components of a building, such as walls, floors, and structural elements.

NEW QUESTION # 65
Where would you find information pertaining to the seismic load?

• A. Electrical plans
• B. Fire protection system plans
• C. Structural plans
• D. Mechanical plans

Answer: C

Explanation:
Information pertaining to seismic loads would be found in the structural plans. These plans contain details about the building's framework and its ability to resist seismic forces. The structural plans include calculations and specifications that ensure the building's integrity under seismic stress, following relevant codes such as the International Building Code (IBC) and NFPA 5000.

NEW QUESTION # 66
Which of the following supporting documents is definedas illustrations and descriptions of a system component taken from a manufacturer's catalog?

• A. Calculation sheet
• B. Cut sheet
• C. Data sheet
• D. Errata sheet

Answer: B

Explanation:
A "cut sheet" is a document that provides detailed illustrations, descriptions, specifications, and other relevant information about a specific system component. Cut sheets are typically taken from a manufacturer's catalog and are used to verify that the components meet the design and performance criteria required for a project.
This type of document is essential for plan examiners, inspectors, and engineers to ensure compliance with relevant codes and standards.
Top of Form
Bottom of Form

NEW QUESTION # 67
In positive alarm sequence systems trained personnel shall have a maximum of how many seconds during the alarm investigation phase to evaluate the fire condition and reset the system'?

• A. 60 seconds
• B. 120 seconds
• C. 180 seconds
• D. 90 seconds

Answer: B

Explanation:
According to NFPA 72, National Fire Alarm and Signaling Code, in positive alarm sequence systems, trained personnel have a maximum of 120 seconds (2 minutes) during the alarm investigation phase to evaluate the fire condition and reset the system. This time frame is provided to allow personnel to assess whether the alarm is legitimate or false before activating a full evacuation or emergency response.
Top of Form
Bottom of Form

NEW QUESTION # 68
Exhibit.

What is the construction type specified for the new addition for plan set Tl?

• A. Type (211)
• B. Type II (111
• C. Type II (000)
• D. Type III (200)

Answer: C

Explanation:
The construction type specified for the new addition in plan set T1 isType II (000). This construction type, as defined in the International Building Code (IBC), refers to buildings with non-combustible materials for all structural elements, but with no fire-resistance rating requirements for any of the structural components. This is typical for newer additions where fire safety is achieved through non-combustible materials and other fire protection systems, such as sprinklers.
Top of Form
Bottom of Form

NEW QUESTION # 69
Exhibit.

On plan F2.0. the fire sprinklers in playroom A14 are supplied by what size cross main?

• A. 1 1/4 in (32 mm)
• B. 2 1 2 m (64 mm)
• C. 1 in (25 mm)
• D. 3 in (76 mm)

Answer: A

Explanation:
On plan F2.0, the fire sprinklers in playroom A14 are supplied by a cross main with a diameter of 1 1/4 inches (32 mm). This size is adequate to deliver the necessary flow rate and pressure required to meet the fire protection demand for a room of this size and occupancy. The sprinkler system design and piping must comply with NFPA 13, Standard for the Installation of Sprinkler Systems, which outlines the required sizing and installation practices for fire protection systems in various types of occupancies, including playrooms and similar spaces.

NEW QUESTION # 70
......

Pass Guaranteed Quiz 2025 Realistic Verified Free NFPA: https://www.validexam.com/CFPE-latest-dumps.html

CFPE Exam Questions - Real & Updated Questions PDF: https://drive.google.com/open?id=1s0vA7GHvB4nfYowUEnPRjTtiOYYCb_W6